Jump to content
Banhammer Forums

flatscreenprintingmachine

Members
  • Content Count

    20
  • Joined

  • Last visited

About flatscreenprintingmachine

  • Rank
    Newbie
  1. flatscreenprintingmachine

    How Does Stenter Dry

    The drying process of Stenter ink The drying process of the ink consists of two steps. The first step, oxidation, is a process through which oxygen interacts with the oil in the ink and the mixed ink to form a solid. The second step is absorption. After this process, the solvent enters the paper and allows oxygen to touch the oil or mixed ink. If the speed of the solvent entering the paper or coating is not fast enough, it will reduce the reaction speed of oxygen, oil and varnish, and eventually extend the dry moment. With this in mind, let us pay more attention to the boring process. When the ink starts to print on the substrate, the solvent in the ink will enter the gaps in the fibers or coatings of the substrate. The pigment remains in the dry oil part, which fixes the pigment on the printed surface. But this is not completely boring yet. Because of the loss of the solvent, the ink film becomes very viscous. In this way, the ink loses its fluidity and stops there to prepare for change. Following the loss of solvent, oxygen reacts with oil, and the resin begins to dry. During this period, the ink appearance is fixed and will not transfer to another sheet of paper in the stack. However, the ink at the base of the ink film still adheres to a certain liquid state. Depending on the composition of the ink, the thickness of the printing ink film, the properties of the paper or other raw materials, and environmental conditions, it may take two minutes to more than one and a half hours for the ink to be completely fixed. After printing, oxidation occurs in alkyd resin or dry oil, and perhaps also in resin. This polymerization result constitutes the three-dimensional, network structure of the chemical binder. Oxygen reacts with all the oils and resins in the ink to convert the liquid material in the ink film into a solid, so that the ink is completely dry. If you leave the linseed oil open, the same response will occur. Oxygen will react and intersperse with the linseed oil, eventually hardening. A paper or coating with a very tight appearance will slow the penetration of solvents. Therefore, there will be solvent residues in the ink, and it will dry up with the reaction between oxygen and oil and varnish. Of course, this will also add boring moments of ink. In order to speed up drying, use a "drying agent" in the ink to speed up the oxidation process. The two most widely used and longest used desiccants in industry include the following: Cobalt: can speed up the process of boring appearance (fixed). Since cobalt is blue, it becomes brown in the dry period, and it is easy to fade the white color. Moreover, it is easily soluble in organic acids, so acid fountain solution with too low PH value (below 4.0) has an effect on it. Manganese: It can speed up the internal drying process and is a more powerful drying agent than cobalt. This desiccant is brown, but it has less effect on white than cobalt, and it does not easily enter the fountain solution. In the process of printing operation, a mixture of these desiccants is usually used to speed up the external and internal desiccation at the same time so as to complete the desiccation process. According to the following part of the process, printers can overcome the boring question of ink: 1. Review the work with the ink supplier before printing, including the paper used. The best solution to boring questions is to prevent them. All paper is different. For example, the dryness of ink on newsprint is completely different from the dryness of ink on papers like SpringhillOpaqueSmooth. 2. When printing on paper with a fine surface, avoid using soybean oil-based ink. Soybean oil is semi-dry (slow) oil. 3. Keep the pH of the fountain solution within the range of 4.0 to 5.0. The higher the acidity (the lower the PH value), the slower the drying process of the ink. 4. When printing a large area of solid land, use a blending oil including desiccant or a clear scale for overprinting. 5. Use the recommended amount of desiccant for the ink being used. Too much desiccant will plasticize the ink so that it is not boring 6. Mixing additional desiccant in the fountain solution can improve the desiccation function of the ink. GrafOSiec is an example of an additional desiccant, which can be added in an amount of 1% to 3%. 7. Make the paper stack lower at the receiving end of the printer. 8. Use large particles of dust to help separate the paper after printing, and allow more oxygen to enter and react with oil and resin. 9. Let the supplier add the strength of the ink, so that it can be printed with a thinner ink layer, which can be fixed and boring more easily. 10. Since the temperature of the printer or paper may be too low and will delay ink drying, pre-process the paper before printing. 11. Remember that the ink composed of ReflexBlue extends the boring moment. Comment with the ink supplier. 12. There must be a dull moment of satisfaction before running or changing jobs. 13. Use infrared drying to speed up ink drying. 14. Remember that the ink used for film printing will be fixed and hardened on the tough film for a few hours. Moreover, the best action plan for Flat Screen Printing Machine is to review the work and paper to be used with the ink supplier. Some ink dryness is suspected to be the result of improper carriers, which result in a low oxidation process or a lack of usable catalysts. The oxidation rate can be increased by adding more oil or alkyd resin in the catalyst, or by using thoroughly dry materials, such as linseed oil or tung oil, instead of semi-dry oil, such as soybean oil.
  2. flatscreenprintingmachine

    Advances In Flat Screen Printing Machine Technology

    Stenter's printing technology is also called screen printing technology, which is a stencil printing technology, and this printing technology originated in China. The screen printing technology is to print the ink from the mesh of the pattern to be printed onto the substrate by squeezing the ink through the squeegee, thereby forming the same pattern or text on the substrate. Applications: LCD glass, lens glass, packaging boxes, light-emitting sheets, sheet glass, mobile phone lenses, display screens, panels, nameplates and acrylic films, touch screens, light guide plates, TV, circuit industry, plastic bags, optoelectronics industry, single , Double-sided, multi-layer circuit boards, PCB boards, liquid green oil, flashing films, flexible circuit boards, flexible circuits, membrane switches, IMD, IML, stickers, heat transfer films, trademarks, labels, nameplates, non-woven Cloth bags and so on. The products printed by the screen printing technology of the screen printing machine are bright in color, and can be stored for a long time, and are also suitable for mass industrial production, so the application of the screen printing machine in industry has considerable prospects. We can also see screen-printed products everywhere in our lives, such as automotive glass, home appliance glass, home appliance trademarks, packaging boxes, tattoo stickers, etc. As long as it is flat screen printing, it can be done with a screen printing machine, and the application industry is very wide. The advantage of screen printing machine printing is that it is not limited by the shape and size of the printed article. In the meantime, as long as it is a flat surface or a curved spherical surface, it can be printed by a screen printing machine. For example, commonly used pens, cups and tea sets, circuit boards on household appliances, or some electrical appliances, such as buttons on mobile phones, as well as logos on the signs of everyday clothes, as well as patterns on clothes and shoes, are all acceptable. Use silk screen printing machine to print. Larger objects, such as text patterns or logos on TVs, refrigerators, and washing machines, can all be printed with a screen printer. And commercial advertising signs, stickers, packaging, etc. can all be printed by screen printing technology. The industrial application of screen printing technology, which is always a screen printing machine, is quite extensive. With the continuous development of modern Flat Screen Printing Machine technology, industrial screen printing technology has realized automated unmanned printing, adapted to mass printing in modern industry, and truly realized the effect of unmanned automatic production, which greatly reduced the company’s Cost has improved production efficiency and brought greater profit growth to the enterprise.
  3. flatscreenprintingmachine

    How To Clean The Flat Screen Printer Chain

    Precautions for Stenter chain Do not directly soak the chain in strong acid and strong alkaline cleaning agents such as diesel, gasoline, kerosene, WD-40, degreaser, because the inner ring bearing of the chain is filled with high-viscosity oil, once it is washed off Afterwards, it will make the inner ring dry, no matter how much low-viscosity chain oil is added afterwards, it will not help. Suggested cleaning method Hot soapy water, hand sanitizer, or a discarded toothbrush or a slightly harder brush, can be washed directly with water. The cleaning effect is not very good, and it needs to be wiped dry after cleaning, otherwise it will rust. Special chain cleaners are generally imported products with good cleaning effect and good lubrication effect. They are sold in professional car shops, but the price is more expensive. Taobao also sells them. Bikers with better economic foundations can consider them. For metal powder, find a larger container, take a spoonful and rinse with boiling water, remove the chain and put it in the water to clean it with a harder brush. Advantages: It can easily clean the oil on the chain, and generally does not clean the butter in the inner ring, it is not irritating, and does not hurt your hands. This thing is commonly used by masters who do mechanical work to wash their hands. . You can buy them in larger hardware stores. Disadvantages: Since the auxiliary is water, it takes a long time to wipe or dry the chain after cleaning. Washing the chain with metal powder is my usual cleaning method. I personally feel that the effect is better. I recommend it to all riders. If any rider has objections to this cleaning method, I can give advice. Bikers who need to remove the chain frequently for cleaning are advised to install a magic buckle, which saves time and effort. Lubrication of the chain After each cleaning, wiping or cleaning the chain with solvent, add lubricating oil, and make sure that the chain is dry before adding lubricating oil. First, penetrate the lubricating oil into the bearing part of the chain, and then let it become viscous or dry. This can surely lubricate the parts of the chain that are easy to wear (the two joints on both sides). A good lubricating oil feels like water at first and is easy to penetrate, but after a while it will become thicker or dry, and can play a lubricating effect. After applying lubricating oil to the chain of Flat Screen Printer, use a dry cloth to wipe the excess oil on the chain to avoid adhesion of dirt and dust. Before reinstalling the chain, remember to clean the interconnection of the chain to ensure that there is no dirt left. After the chain is cleaned, some lubricating oil must be applied to the inside and outside of the shaft when assembling the magic button.
  4. Flat Screen Printing Machine scraper holder experience: The squeegee frame of the printing machine must be regularly checked for straightness. The tool holder will be deformed in long-term use. We only need to use a straight edge ruler to close the surface of the tool holder, so that it is easy to find out whether it is deformed. When installing the scraper on the knife holder, make sure that the clamping plate and the knife holder are parallel. In most cases, the length of the scraper is longer than the splint. Usually there is a step on the scraper frame to locate the rear edge of the scraper, and make sure that the edge of the step is in good condition during use. If bolts are used to fix the scraper, make sure that they and the threads are clean and in good condition. Tighten them with a fixed-torque wrench, and set a suitable torque value first, so that after the bolts are tightened, the same pressure will be used to allow the pressure plate to clamp the scraper. The steps to tighten the bolts are from the middle to the sides to the extreme edges. The parallelism between the doctor blade and the anilox roll requires regular correction. Whether it is a single scraper or an ink chamber system, the knives and the anilox roller must meet the requirements of the upper and lower knives and the left and right edges of the knives when they are installed. If there is any non-parallelism with the anilox, this requires more pressure to scrape the ink cleanly , But this will cause the contact angle between the doctor blade and the anilox roller to become smaller than the optimal angle, which will cause printing problems Regularly check and correct mechanical parts, center points, inflatable shafts, bearings, etc., check for mechanical damage or wear, and repair or replace them according to actual conditions. Stenter's plastic squeegee can be used in many places with a good side, but there are also unsuitable places such as solvent ink supply systems or high-temperature environments. Contact your supplier or test the scraper sample with solvent to verify suitability.
  5. Stenter needs to consider some basic factors when using it: color number and station The automatic garment printing machine has six colors and 24 stations, and there are also 6 colors and 32 stations, which can be customized. The station of the automatic printing machine is usually 6 more than the color number to facilitate the laying and picking of the film. Some configurations are specially designed for one operator to operate, and only one more workstation is installed to lay out and take the film. When deciding how many stations you want, you must consider the need for flash curing stations. Pneumatic, electromechanical transmission and servo mechanical transmission are common types in the operation of automatic printing machines. Some printing machines use one type of transmission, while others use a combination of multiple transmission methods. The pneumatic system uses compressed air to adjust the pressure of the scraper and the ink-returning knife of the printing machine, and the solenoid valve can control the speed and movement distance. Printing machines with strict pneumatic transmission systems are usually cheaper than those with electromechanical transmission or servo mechanical transmission. Most automatic printing machines are equipped with pneumatic screen frame clamping devices. They only clamp a few sides of the screen frame. It is equipped with a positioning pin registration system, which helps to speed up the alignment of the screen plate on the printing machine. The size of the screen frame determines the area of the screen that the printing machine can accept. If this kind of automatic printing machine does not support the size of the screen frame you are currently using, you must change it to a new screen frame, which is very wasteful. So pay attention to the machine model, and the screen frame must be able to switch freely between sizes. Cycle speed may be a factor that is more important when buying Flat Screen Printing Machine. The larger cycle speed refers to the output of the printing machine in one hour when operated by one or two workers. Some printing machines can print hundreds of clothes per hour, and some can print more than 1,000 clothes. In fact, the actual cycle speed depends on the number of flash drying processes in your workflow, whether the paste can reach the surface dry in a very short time, and also related to factors such as the printing paste, printing area, and fabric.
  6. flatscreenprintingmachine

    Equipment Adjustment Of Flat Screen Printing Machine

    With the improvement of printing technology, many printing equipment are active in the market. Among them, the fully automatic screen Stenter is the hottest printing equipment in the printing industry. In the printing process, the size adjustment of the fully automatic screen printing machine is a big problem, so what needs to be done to ensure the size adjustment is in place? 1. Adjust the parallelism of the guide rail, printing plate and worktable of the automatic screen printing machine 2. The adjustment platform and the guide rail are on the same parallel surface 3. The screen printing plate and the printing press platform need to be parallel 4. The distance between the screen of the automatic screen printing machine and the product should be within 2-5mm 5. Make sure the blade of the Flat Screen Printing Machine is sharp
  7. flatscreenprintingmachine

    How To Turn On The Open Rotary Screen Printer

    1 Turn on the Hot Air Stenter 1.1 Click the cloth feeding mechanism button to enter the cloth feeding mechanism operation interface, and click the cloth feeding master control switch in the upper left corner to red. 1.2 Click the cloth discharging mechanism button to enter the cloth discharging mechanism operation interface, and click the cloth discharging master control switch in the upper left corner to red. 1.3 Press the reset button "RESET" on the operation panel, the indicator light is off, the start indicator flashes, press down the start indicator, the chain rotates, and the acceleration indicator flashes. 1.4 Click the oven button to enter the heating system: a. Click the icon of the circulating fan to enter the circulating fan power setting window, click the total button of the circulating fan to pop up a small window for setting the circulating fan power, click on the white bottom number box to pop up a numeric keypad, enter the required output power value, and press OK. b. Click the upper left corner or the upper right corner of the exhaust fan icon to enter the exhaust fan power setting window, click the manual control button and confirm, click the number box on the white background to pop up a small numeric keyboard to enter the required value and confirm. If you click the automatic control button and confirm, the fan will automatically adjust the power of the fan. Click the digital box showing the temperature in the oven simulation icon to enter the heating window, click the heating total to set the heating temperature, or you can set the heating temperature of each oven separately. When the heating temperature is below 90 degrees, click the small fire icon to heat, and when the heating temperature is above 90 degrees, click the big fire icon to heat and confirm. 1.5 Correct threading route, put the cloth in the cloth feeding part and guide the cloth 9 from the cloth feeding frame to the operating table), and wear the cloth-out part guide belt along the correct threading route (from the cloth overfeeding roller to the cloth outlet frame) ). 1.6 Press the red stop button on the operation panel, the chain stops, and the start indicator flashes. Pull the guide cloth onto the tentering chain and press the overfeeding wheel push button for about 10 seconds, and wait for the push button indicator to light up. Turn on the motors of each part of the cloth feeding mechanism to "1". Raise the pour chute, apply the pressure of the rolling car, turn on the motors of all parts of the operating table (except the needle protection entrance button), and click the cloth feed control button in the upper left corner of the cloth feed mechanism to green. 1.7 Start the front part of the machine. After the cloth guide has passed the upper needle protection entrance, turn on the upper needle protection entrance button to "1". When the cloth guide goes out of the oven and reaches the cloth overfeeding roller, stop the machine, and connect the cloth guide to the cloth exit part. The conduction band is connected well. Click the main control button of the cloth discharging mechanism to green, turn on the motors of the cloth discharging part to "1" (except the cooling cylinder tension motor switch), restart the machine, introduce the cloth guide into the cloth discharging rack and stop. Turn on the switch of the cooling cylinder tension motor to "1". 1.8 Click the tentering chain control button to enter the chain control interface, enter the width according to the process requirements on the process card and confirm 1.9 According to the process card, find the cloth to be processed and push it to the cloth feeding place to connect the guide cloth, melt the material and put it into the pouring tank (the first 20L is discharged). According to the organization condition of the cloth to be processed and the technological requirements, the cloth rolls or the car is installed. Set the parameters of each part, according to the weft skew of the fabric to be processed, preset the middle fast/middle slow, left fast/right fast of the weft trimmer. Ring the bell to notify that the cloth is ready for the open rotary screen printer to turn on. After the ring returns, press the power button, the acceleration indicator flashes, set the speed required by the process and confirm, click the acceleration button and the speed will automatically increase to the required speed.
  8. The fully automatic Stenter can produce all kinds of porcelain, metal, glass, wood and other utensils and fabrics. Because the fully automatic Stenter has a simple process, no plate making, no printing, convenient operation, suitable for on-site production, low production cost, and high profit. So how to make the fully automatic Stenter use longer? Here is what licheng Flat Screen Printing Machine Factory shares for you: About the transportation and maintenance of compressed air 1. When delivering compressed air, air leakage should be avoided to save electricity costs. The air pressure used should be kept below 6 kg, and the air pressure source should be 7-8 kg. Therefore, the starting pressure point at the bottom of the set air compressor must be greater than 7 kg. 2. Compressed air conditioning device: Since the fully automatic Stenter is driven by pneumatic components, the composition of the compressed air has a great influence on the air pressure system. The compressed air contains impurities. Know: dirt, rust, dust, etc., these dirt In the pneumatic components, the wear of the components will be accelerated, their performance will be affected, and their service life will be shortened. Therefore, in the design of the air pressure pipes of the machine, before the compressed air enters the machine, a set of air conditioning devices (usually called two-pieces) is added. , To protect the various components of the machine's air pressure system. About the maintenance and maintenance of printing machinery parts Selection of operating site: It should be far away from places with high dust volume and high room temperature to ensure the stability of printing quality and the service life of software, thereby saving costs. In order to effectively extend the service life of the fully automatic Stenter, the equipment must be regularly repaired and maintained. This will not only extend the service life of the equipment, but also ensure a safe and comfortable working environment. The fully automatic Stenter slowly replaced the previous low-efficiency mode of manual printing plates. And with the fully automatic Stenter, it is necessary to achieve clean, clean, firm, lubricated, anti-corrosive, and safe work content, working methods, tools and materials used, standards and precautions.
  9. Accompanied by the use of Hot Air Stenter in various fields. More and more customers choose to use Hot Air Stenter for manufacturing. But there are also many new customers who do not understand some basic knowledge of Hot Air Stenter. Today's web editor will give everyone a detailed introduction to these aspects. 1. Hot Air Stenter is a new technology printing-free full-color digital printer: it will not be limited by all raw materials, it can be used in T-shirts, sliding doors, cabinet doors, sliding doors, laminated glass, plates, various Color photo-level packaging printing is carried out on the surface of identification plates, amethyst, PVC, acrylic sheets, metal materials, plastics, marble, and leather products. It does not require printing and plate making, one packaging printing process, bright and colorful colors, anti-wear, blocking ultraviolet rays, simple and convenient actual operation, faster packaging and printing images, and in line with actual industrial production packaging and printing specifications. 2. Hot Air Stenter is suitable for packaging and printing of diversified materials. As far as the packaging and printing manufacturing industry is concerned, there are more technical and professional manufacturing industry differences. For example, the traditional packaging printing in the leather product manufacturing industry: ink printing has a single color tone and simple color connection; large and medium leather printing machines are expensive. , High requirements for materials; thermal transfer process will destroy materials. The traditional packaging printing method in the amethyst manufacturing industry is amethyst glass film processing technology. The plexiglass plate manufacturing industry uses screen printing, and the metal material manufacturing industry uses thermal transfer printing technology. So once you have a Hot Air Stenter, you also have a stronger core competitiveness than the same industry 3. Hot Air Stenter's packaging and printing positions are accurate, preventing the problem of position deviation encountered by hand-made printing plants. Hot Air Stenter no longer uses traditional packaging and printing methods and methods, and is no longer the simple manual service actual operation and technical packaging printing in the past. It has developed a stronger technology with high-tech computer generation and automatic control technology. The organic combination can accurately point to the areas and parts that need to be packaged and printed, and prevent the problem of position deviation encountered by hand-made printing plants. Because it is a one-time multi-color packaging printing, there will be no problems with overprinting. This kind of advantage can also be combined with hand-carving and etching processes in a very reasonable way. Packaging and printing beautiful pictures in hand-carved areas, or carrying out precise etching processes after packaging printing, can also be obtained in the hand-carving manufacturing industry. Good promotion. 4. The packaging and printing process is unusually simple. Hot Air Stenter does not use the process of printing plate making, ink printing, and repeated overprinting, and does not use various types of special tools and raw materials necessary for ink printing and thermal transfer process methods. To choose your open rotary screen printer, you only have to prepare a general computer in advance. A machine operator can completely carry out the actual operation of packaging and printing alone, saving capital investment, and the method is simple and immediately desirable. The work experience of the operator is low, and it is enough to master simple picture and image processing software.
  10. We usually wear or use some textile products, clothing, etc., when processed into the products we need, all need to go through a process, that is, stenting and setting, so we must use Stenter. Especially for plain woven fabrics such as cotton, linen, chemical fiber, and blended fabrics, a series of devices are required to complete this process in each section of cloth feeding, cloth feeding, and cloth feeding. When we talk about the Stenter, we must know that it is a device specially used for stenting and heat setting. However, it has another feature, that is, the Stenter can generate a large number of positive and negative charges. These charges can Neutralize the charge on the object. If the surface of an object has a negative charge, it can attract the positive charge in the airflow, otherwise it will attract the negative charge in the airflow to neutralize its own positive charge. In this way, no matter what kind of electric charge the object itself has, it can be neutralized, eliminating static electricity. It can be called a fixed static elimination special equipment, simple and easy to operate in installation, stable performance and other characteristics. But still need to introduce its main function. The so-called Stenter is to complete the setting process of the fabric, usually using heat-conducting oil to heat the air in the Stenter to achieve the purpose of heating the fabric. After the temperature reaches a certain period of time, it will promote the structural change of the fabric, thus setting it into The intended goal. With the continuous updating of technology, Stenter has been equipped with a monitoring system. Synthetic fiber has strong wear resistance. If it is used to replace metal mesh, the service life is increased by five times, and the economic benefit is greatly increased. In terms of technology, more different patterns can be woven. There is also a proprietary design based on the unique properties of hot air dynamics, which is conducive to maintaining a doubled and balanced amplitude temperature distribution. This ensures that some fabrics with high moisture content are still plastic when they are shaped by the Tenter Open Type Rotary Screen Printing Machine. When they are dried, the condition of the warp and weft yarns in the fabric can be appropriately adjusted to make the fabric width Pull to a predetermined size to achieve the purpose of unchanged form.
  11. flatscreenprintingmachine

    Stenter Control Ink

    In the work of the fully automatic Flat Screen Printing Machine, the printing of ink is particularly important to the printing machine. The best way to control the drying speed of the Flat Screen Printing Machine ink is to reach an agreement with the ink supplier to determine what you want to print, and the other party must provide Which inks. How to control printing ink on Flat Screen Printing Machine? Today, the staff of Licheng Printing Machinery will introduce to you: 1. Try not to use soybean-based ink in the printing process, because soybean oil is semi-dry (slow) oil, so it is not easy to dry when the paper is dense. 2. The best solution to the drying problem is to prevent it. It is necessary to communicate clearly with the ink supplier before printing. The Flat Screen Printing Machine ink supplier knows their products better than the printer. Where is the ink used? For example, trademark nameplates are printed on paper. Even if different papers are used for printing, the inks are also different. For example, the drying of ink on newsprint is completely different from drying on a type of paper. 3. The printing environment should control the pH value of the fountain solution to be between 4.0 and 5.0. Higher acidity (lower PH value) will slow down the drying process of the ink. 4. Adding a desiccant to the fountain solution can improve the dryness of the ink. 5. Use large particles to spray powder to separate the printed paper and allow more oxygen to enter, causing it to react with oil and resin. 6. Let the supplier increase the strength of the ink so that it can be printed with a thinner ink layer, making it easier to fix and dry. 7. Since the temperature of the printing press or paper may be too low, the paper is pretreated before printing, which will affect the drying of the ink. 8. When printing on a large area, overprinting should use varnish containing desiccant or use transparent ink. 9. Use the recommended amount of desiccant for the ink in use. Too much desiccant will harden the ink and cause the ink to not dry. The above is the introduction of how to control all Stenter printing inks, and I will stop here today. Finally, I remind everyone to choose the right ink, and then grasp the points to pay attention to in the details.
  12. The main purpose of Hot Air Stenter Machine is to shape continuous silk threads according to the weaving conditions after merging and twisting, that is, it is used to shape chemical fibers, real silk, cashmere, yarn, curtains, crepes, and printed fabrics. That is to say, the non-twisted yarn with stable twist and balance under certain pressure and temperature is convenient for subsequent processing and improves product quality. Flat Screen Printing Machine Factory For yarns with strong twists, the use of fabric setting machines is more important. The Hot Air Stenter Machine has a wide range of applications. It can be used for both moist heat setting (saturated steam directly enters the cylinder) or dry heat setting (saturated steam directly enters the jacket and dissipates heat from the inner wall of the cylinder). The door switch is light and flexible, and the loading and unloading of objects is quick and convenient. Hot Air Stenter Machine features: 1. Hot Air Stenter Machine computer touch screen, fully automatic one-key operation, high output, finalized in batches. 2. Hot Air Stenter Machine incense selection, eliminate peculiar smell, increase atmosphere, high temperature sterilization, health and safety. 3. Computer servo system with frequency conversion function, energy saving and electricity saving. Fast heating and automatic setting, so that the fabric can be heated evenly at 360 degrees, which is efficient, fast and convenient. 4. High-temperature ironing can accelerate the volatilization of harmful substances (such as formaldehyde and chemical dyes) remaining on the fabric. 5. One machine with dual functions, can form finished and semi-finished products. Hot Air Stenter Machine is equipped with a computer-adjusted temperature setting controller, which can be used for steam setting according to different fabrics. 6. The pattern setting function can solve the problem of fabric pattern misalignment and make the flowers align accurately.
  13. flatscreenprintingmachine

    Introduction To The Purpose Of Stenter

    The main purpose of Stenter is to shape continuous silk threads according to the weaving conditions after merging and twisting, that is, to shape chemical fibers, real silk, cashmere, yarn, curtains, crepes, and printed fabrics. That is to say, the non-twisted yarn with stable twist and balance under certain pressure and temperature is convenient for subsequent processing and improves product quality. For yarns with strong twists, it is more important to use a fabric setting machine. The fabric setting machine has a wide range of applications. It can be used for wet heat setting (saturated steam directly enters the cylinder) or dry heat setting (saturated steam directly enters the jacket and radiates heat from the inner wall of the cylinder). The door switch is light and flexible, and the loading and unloading of objects is quick and convenient. Features of fabric setting machine: 1. The fabric setting machine computer touch screen, fully automatic one-key operation, high output, finalized in batches. 2. Fabric setting machine incense selection, eliminate peculiar smell, increase atmosphere, high temperature sterilization, health and safety. 3. Computer servo system with frequency conversion function, energy saving and electricity saving. Fast heating and automatic setting, so that the fabric can be heated evenly at 360 degrees, which is efficient, fast and convenient. 4. High-temperature ironing can accelerate the volatilization of harmful substances (such as formaldehyde and chemical dyes) remaining on the fabric. 5. One machine with two functions, can form finished and semi-finished products. The Flat Screen Printing Machine is equipped with a computer-adjusted temperature setting controller, which can perform steam setting according to different fabrics. 6. The pattern setting function can solve the problem of fabric pattern misalignment and make the flowers align accurately.
  14. Now the Hot Air Stenter Machine impeller nozzle mechanism is used. The top of the blow tube is equipped with a sealing ring, which is welded to the mounting plates on both sides of the hair. The top of the mounting plate is equipped with sensors, which are connected to the rod and fixed protrusions to fix the welding current collector. In the inner wall surface of the top of the body, the bottom of the shaft is provided with a clamping sleeve, and when the plate assembly is connected to the adjustment plate by passing through the positioning rod and the telescopic rod, the spring plate is arranged on the inference part adjustment plate, and the air nozzle is arranged on the elastic The lower part of the board. Hot Air Stenter Machine air nozzle installation requirements At present, the design of the overall structure of the installation mechanism is simple and reasonable, the operation is flexible and convenient, the air supply effect is more complete and uniform, and the utility is stronger. The dust collector of the entrance Hot Air Stenter Machine has an exhaust fan and fixed on the sliding frame. The upper suction trough, the vent is connected through the bottom of the vacuum suction trough, the air outlet of the exhaust fan is connected with the air outlet pipe, the upper end of the dust suction net is fixed in the frame of the dust suction net, and the grid ribs are formed in the suction net. In the frame, the upper end of the suction pipe forms the upper end of the dust suction net, the dust is inserted into the frame of the dust suction net, the cylindrical cover forms a cylindrical ring groove cover, and the vacuum net frame is inserted into the ring groove of the bucket cover. Since the electromechanical setting includes the tension adjustment of the Hot Air Stenter Machine, the upper furnace unit is set on the top of the lower furnace unit, the chain feeds through the unit furnace top and the furnace bottom unit, and the feed chain is tensioned on the drive sprocket to follow On gears, vertical external gears and internal vertical gears, the bottom of the front case is equipped with a feed roller, and the Hot Air Stenter Machine center at the bottom of the front case is adjusted to apply between the fabric and the roller so that the Hot Air can be applied. Stenter Machine is placed in the factory application. The current Hot Air Stenter Machine cooling device of Flat Screen Printing Machine Factory, its main flue is in the drying box and molded, the flue is located in the duct main flue, the flue is vertically fixed to one side of the main flue, and the main flue is connected to The flue and the condensate pipe are surrounded by the main flue. The current structure of the outer wall is simple, which can effectively cool the main flue pipe, reduce the temperature of the main flue pipe, and prevent fires caused by the flue pipe.
  15. There are many factors that determine the value of the Hot Air Stenter Machine brand to consumers. In order to facilitate effective measurement of the different effects of these factors, a somewhat confusing and incomprehensible method is introduced here, including commonly used knowledge and technology. Content and consciousness preference factors. The concept of good and evil is applied, and it focuses on analyzing the subjective value of the product with which the consumer establishes a connection. To create a higher degree of participation and build a stronger brand, it is necessary to pay attention to the improvement of soft qualitative value, and at the same time pay attention to the improvement of hard quantitative value.   Since there are so many factors that determine the brand value of Flat Screen Printing Machine Factory, it is necessary to collect as much accurate knowledge as possible to form the basis for brand building and participation. Continuously inject more and more value into products for its consumers, so that consumers have more opportunities and possibilities to consume it all over the world.
×